Anespa DX

Mineral ion water activator for shower and bath, using a twin cartridge system.

The Anespa DX is a shower and bath water filter. It installs at a bathroom mixer in place of the existing shower head, and passes warm water through two cartridges: an activated carbon fibre cartridge that removes residual chlorine, and a ceramic cartridge containing Futamata Radium Hot Spring ceramic and bamboo charcoal in the form of ceramic balls.

It is not a water ioniser. It has no electrodes, no power supply and no pH settings, and Enagic states the water it produces is the same pH as tap water. A selector valve directs flow either to the shower head or to an outlet pipe for filling the bath.

The unit is 346 mm tall and 130 mm across at the base, weighs 2.5 kg, and is made in Japan.

Specifications

Figures are taken from the Anespa DX product manual unless noted otherwise. Where the manual and Enagic's product pages disagree, the manual is used, because it is the engineering document.

The two flow figures measure different things. Filtering capacity is 8.3 litres a minute at 0.1 MPa and 40 °C — what the cartridge can process. The 2.6 litres a minute figure is the flow at the shower head.

Anespa DX specifications and where each figure comes from
SpecificationValueSource
Model numberANSP-02Anespa DX product manual p.1
Country of manufactureJapanAnespa DX product manual p.1
GeneratesMineral ion water for bath or showerenagic.com Anespa DX product page
WattageNot poweredenagic.com Anespa DX product page
Water connectionBathroom mixer tap via changeover faucetAnespa DX product manual p.1
Source waterMunicipal drinking water compatible with the Water Supply LawAnespa DX product manual p.1
Applicable water pressure0.05-0.5 MPaAnespa DX product manual p.5
Maximum operating temperature60 degCAnespa DX product manual p.5
Target substance eliminatedResidual chlorineAnespa DX product manual p.5
Residual chlorine filtrate1 mg/L at 40 degCAnespa DX product manual p.5
Filtering mediumTourmaline-impregnated activated carbon fibreAnespa DX product manual p.5
Filtering capacity8.3 (2.2 US gal/min) at 0.1 MPa and 40 degC L/minAnespa DX product manual p.5
Maximum flow rate15 L/minAnespa DX product manual p.5
Shower flow rate2.6 (0.69 US gal/min) L/minenagic.com Anespa DX product page
pH rangeSame as tap waterenagic.com Anespa DX product page
Ceramic cartridge compositionRadium and bamboo-charcoal ceramic ballsAnespa DX product manual p.3
Ceramic cartridge stonesTufa, Mic stone and Power stoneAnespa DX product manual p.3
Tufa sourceFutamata Radium Hot Spring, Hokkaido, JapanAnespa DX product manual p.3
Base magnetNeodymium magnet in the baseAnespa DX product manual p.3
Water purifying cartridge lifeApprox. 1 yearAnespa DX product manual p.5
Ceramic cartridge lifeApprox. 3 yearsAnespa DX product manual p.5
Dimensions (H x diameter)346 x 130 mmAnespa DX product manual p.5
Gross weight2.5 kgAnespa DX product manual p.5
Changes in the DX modelLarger ceramic cartridge holding more ceramic balls; redesigned base for filter replacementenagic.com Anespa DX product page
CertificationsEnagic International holds ISO 9001, ISO 14001 and ISO 13485 at company level, not product-specificenagic.com Anespa DX product page

Price by country

Enagic sets its price separately in each country. These are the published prices before tax; each country's price list shows the tax, the total and the payment plans.

CountryOptionPrice before taxFull price list
Australia$3,450.00 AUDAustralia price list
Canada$3,850.00 CADCanada price list
United States$3,420.00 USDUnited States price list
New Zealand$3,700.00 NZDNew Zealand price list
United Kingdom€2,800.00 EURUnited Kingdom price list

Maintenance

The Anespa DX has two cartridges on two different clocks. The clean water cartridge is replaced about once a year; the ceramic cartridge about once every three years. Both intervals vary with water quality and how much water is used. Enagic warns that continuing past the exchange point may lead to clogging.

The two cartridges have similar names and different intervals, and Enagic states it does not accept responsibility for incorrect filter orders — so it is worth confirming which one is being ordered before placing the order.

Replacement is the only owner-serviceable procedure Enagic describes. The ceramic cartridge goes in first and the clean water cartridge fits over it. After fitting a new cartridge, and before using the unit for the first time, run water through it for two to three minutes. If the unit has stood unused for two or three days, run water for one to two minutes first.

Three conditions Enagic sets out that are easy to miss. Water at 40 °C or above must not be passed through the unit. The tip-resistant ring must be fixed to the wall and attached to the unit, because a unit full of water is significantly heavier than an empty one. And the water inside must not be allowed to freeze — where that is a risk, Enagic says to let a small quantity of water pass through.

Water that has passed through the unit has been dechlorinated and Enagic advises against storing it.

Replacing the cartridges in an Anespa DX

Questions

What does an Anespa DX cost in Australia?

The recommended price is $3,795 including GST, which is $3,450 before GST. Instalment plans are available over three, six, ten, sixteen or twenty months.

Can the Anespa DX be paid off monthly?

Yes. Enagic's E-Payment plan runs from three months at $996 after an initial payment of $997, to twenty months at $150 after an initial payment of $1,105. The plans cost more than paying outright — $190 more over three months and $310 more over twenty.

Is the Anespa DX a Kangen Water® machine?

No. It has no electrodes, no power supply and no pH settings, and it does not produce Kangen Water. It filters and passes water over ceramic media. Enagic states the water it produces is the same pH as tap water.

What does the Anespa DX remove?

Residual chlorine. Enagic states the target substance of elimination is residual chlorine, filtered at 1.2 mg/L at 40 °C, using an activated carbon fibre cartridge. No other contaminant reduction figure is published for this product.

How often do the cartridges need replacing?

The clean water cartridge about once a year, the ceramic cartridge about once every three years. Both vary with water quality and consumption.

Where does the Anespa DX install?

At a bathroom mixer, in place of the existing shower head. It needs a working pressure between 0.05 and 0.5 MPa and water compliant with drinking water standards. Enagic states the unit must not be used when nearby water works are underway or when rusty water appears.

What is the difference between the Anespa DX and the earlier Anespa?

Enagic describes two changes: a larger ceramic cartridge holding more ceramic balls, and a redesigned base intended to make filter replacement more efficient. This is the only account of the difference that Enagic publishes.

Is the Anespa DX sold in Australia?

Yes, by Enagic Australia, through independent distributors.

Order online

Order online here. Choose what you're ordering, then fill in and sign Enagic's own order forms, with your own independent distributor or one we find for you. Enagic processes the order and takes payment. Kanjuni doesn't sell Enagic products.

A woman filling a glass with water at a kitchen tap