E-Cleaning a LeveLuk K8
E-Cleaning removes calcium that has built up on the electrodes inside a LeveLuk K8. The machine runs the cycle itself once you have fitted the cleaning tank and cartridge and started it from the touch display. It takes about three hours, plus a five-minute rinse.
The K8's procedure is not the one published in Enagic's general E-Cleaner instructions, which describe a cleaning powder unit left to soak overnight. The K8 uses a cleaning tank, a cleaning cartridge and a guided cycle on the display. Following the general instructions on a K8 will not work: the machine will not recognise the tank and will show a tank error instead. Check the manual for your own model rather than assuming any Enagic machine cleans the same way.
Everything below is from Enagic's own operation manual for the machine. Kanjuni is an independent platform and is not affiliated with Enagic International.
Source: Enagic LeveLuk KANGEN8 Operation Manual, EN23–EN28.
When to clean
Enagic's manual recommends E-Cleaning once every week or two weeks.
The manual also names E-Cleaning as the fix for four specific symptoms, which are worth knowing because they are what usually sends someone looking for this page:
- Output of all types of water is getting low — after checking water pressure and whether the filter has clogged.
- Whitish material floating or settled in Kangen Water® — calcium processed by electrolysis. The manual describes this as harmless.
- Kangen Water® pH dropping below the normal range when producing Kangen Water® and Beauty Water, caused by calcium building up in the ionising cell.
- A pH measurement below the normal range, where the cause is reduced electrolysing performance rather than soft tap water.
Hard water builds calcium up faster, so the interval that suits a given machine depends on local water rather than on a fixed schedule.
Auto cleaning is different
The K8 already cleans itself, and that is not the same thing as E-Cleaning.
KANGEN Refresh runs for about 10 seconds when the tap is closed after Kangen Water® or Beauty Water has run for more than 10 minutes.
Cleaning runs for about 30 seconds when another processed-water mode is selected after making Strong Acidic Water, or when the unit has not been used for more than 24 hours. The display shows a cleaning notification and asks for water to be run.
Neither cycle uses cleaning powder, and neither removes established calcium build-up. The water discharged during both is cleaning water and the manual says not to use it.
What you need
- 400ml of water
- Two packets of Enagic cleaning powder. The manual is explicit that another manufacturer's powder may damage the unit.
- The cleaning tank, with its additive cap
- The cleaning cartridge
- The red cap, for the secondary hose
The cleaning powder contains citric acid, which Enagic's manual describes as commonly used as a food additive and harmless. If cleaning solution gets in your eyes, the manual says to wash it away immediately.
New K8s ship with a cleaning tank, a cleaning cartridge and six 30g packets of cleaning powder. Replacement powder is sold in boxes of 24.
The procedure
Shut off the tap and turn the unit off before you start. Then open Settings on the touch display and select E-Cleaning — the display walks through twelve numbered screens, and the steps below are those screens.
- Pour two packets of cleaning powder into the cleaning tank, add 400ml of water and mix thoroughly.
- Insert the cleaning tank. Fit the tank cover — without it the machine cannot recognise the tank and shows a tank error.
- Remove the water filter and install the cleaning cartridge in its place, using the holder that normally holds the filter.
- Fit the red cap onto the secondary hose.
- Press start. The display counts down from 3:00.
- When the display shows cleaning is finished, remove the cap from the secondary hose.
- Remove the cleaning cartridge and refit the water filter.
- Remove the cleaning tank and refit the tank you were using before.
- Run water to rinse the machine. The display counts down 300 seconds.
- When the display shows Complete, turn off the water. The unit returns to the home screen.
The water that comes out of the pipe or hose during the cycle and the rinse is cleaning water. The manual says not to use it.
Cautions
Never run water hotter than 40°C through the unit. The manual states this may damage the unit or cause malfunctions, and the machine has a hot-water protection device that will display a warning and stop production above that temperature. Enagic specifies water below 35°C for normal production.
Use only Enagic cleaning powder. The manual states another manufacturer's powder may damage the unit.
The unit contains no user-serviceable parts. Enagic's manual states all servicing must be performed by an authorised service representative, and that modifying, overhauling or repairing the product yourself risks fire or electric shock and voids any claim against the maker.
E-Cleaning is not a repair. If the display shows an ionisation error, an overheat warning, or a message that persists after the corrective action, the manual directs you to unplug the unit and contact your local Enagic branch office.
Filter replacement
E-Cleaning cleans the electrodes. It does not clean or replace the water filter, which is a separate consumable.
Enagic rates the K8 filter at 6,000 litres or approximately one year, whichever comes first — the volume figure is stated per JIS S 3201, the Japanese testing standard for household water purifiers. The machine tracks usage and announces when replacement is due, and the manual notes the notification does not appear while water is running.
The manual names the replacement filter two different ways. The options page lists Activated Charcoal type FC1; the NSF/WQA certification plate on the back of the manual lists Replacement Filter F8. Both appear in the same document. We have reproduced the disagreement rather than choosing one — check the part number against your own machine before ordering.
Run water through the machine for three minutes after fitting a new filter. The manual's precautions page separately says 15 minutes when a filter is first used; both figures are Enagic's.
Sources
Every fact on this page comes from Enagic's own operation manual for the LeveLuk KANGEN8, published by Enagic Australia. The E-Cleaning procedure is EN27–EN28, auto cleaning EN23, filter replacement EN24–EN26, troubleshooting EN31, options EN34 and specifications EN35.
Where the manual and Enagic's websites disagree, the manual is what we publish.
Questions
How long does E-Cleaning take on a K8?
About three hours for the cleaning cycle, then a five-minute rinse. The display counts both down. The machine runs unattended during the three hours.
How often should I E-Clean a K8?
Enagic's manual recommends once every week or two weeks. Harder water builds calcium up faster, so machines in hard-water areas reach the point of needing it sooner.
Can I use the overnight cleaning powder unit method on a K8?
No. That procedure is for older LeveLuk models. The K8 uses a cleaning tank and cleaning cartridge with a guided cycle on the touch display, and it will not recognise a cleaning powder unit.
Can I use a different brand of cleaning powder?
Enagic's manual states that another manufacturer's powder may damage the unit. The supplied powder contains citric acid.
Why does the display say the tank is incorrect?
The manual attributes this to the tank cover not being fitted. The machine cannot recognise the cleaning tank without its cover, and shows a tank error instead of proceeding.
Is the white material in my Kangen Water® a problem?
Enagic's manual describes it as calcium processed by electrolysis and lists it as harmless. It names E-Cleaning as the remedy.
Can I drink the water produced during cleaning?
No. The manual states the water discharged from the pipe or hose during cleaning is cleaning water and should not be used.
Does E-Cleaning replace the filter?
No. They are separate. The filter is rated at 6,000 litres or about a year, and the machine notifies you when it is due.
What are the K8's electrodes made of?
Platinum-plated titanium, per the manual's standard specifications. Calcium deposits on them during normal use, which is what E-Cleaning removes.