Installing an FC1 replacement filter
The FC1 is Enagic's current replacement filter. It replaces both the discontinued F8 and the HG-N, and Enagic states it fits every machine that previously took either of those.
Installation is the same job on every machine, with one difference: how the filter cover comes off. Enagic's own installation video covers three cover types, and the steps below follow it.
The video is a general replacement-filter video rather than an FC1-specific one. The filter it shows being fitted is the same physical part in the same tray, so the procedure applies, but Enagic publishes no FC1-only installation video.
Source: Enagic Canada, “How to install your Enagic replacement filter”.
Which filter you need
Enagic's rule is to open the machine and read the label on the current filter or the filter base.
- If it says F8, HG-N or FC1, order the FC1.
- If it says MW-7000HG, or simply HG, order the HG filter instead. Enagic states this is typically found in older machines.
Enagic publishes a filter spout comparison guide for cases where the label cannot be read, and states plainly that it is not responsible for incorrect filter orders. It is worth confirming before ordering rather than after.
Opening the cover
The cover differs by machine, and this is the only part of the procedure that does.
LeveLuk K8. Slide the filter cover to the left to remove it, then turn the plastic knob from right to left.
Leveluk and other machines. The cover is on the left side of the machine. Push the top centre of the cover and pull it towards you.
SD501 and other models. Push the left centre of the cover and pull it towards you to remove it, then turn the knob of the filter holder from the centre to the left.
In each case, make sure the holder is removed completely from the filter before pulling the filter out.
Checking the seals
This is the step most easily missed, and Enagic gives it its own passage in the video.
The bottom of the filter has two O-rings of different sizes, one installed in each hole. The large O-ring is for the centre hole.
After removing the old filter, check both the filter tray and the bottom of the filter. If the O-rings have stayed behind in the tray holes, they must be put back onto the filter before the new one goes in.
Installing the new filter
Push the new filter into the tray. Put the holder back and turn the knob from left to centre.
While turning the holder, Enagic advises holding down the top of the filter and pushing it away from you slightly.
Once the filter is secured with the holder, check that there is no large gap between the holder and the filter tray. A gap means the holder has not seated.
If the holder does not turn easily, clean the rail that the filter holder runs along, then try again.
Flushing
Before the filter cover goes back on, run water through the machine for a couple of minutes to check there is no leakage.
Doing this with the cover off is deliberate: a leak is visible then and hidden afterwards.
When to replace
Enagic publishes the interval three ways, and they describe the same thing from different angles because filter life depends on how much water passes through it and on the source water.
- Approximately 6,000 litres — the volume figure, published in the LeveLuk K8 manual and repeated by Enagic Dubai for the FC1.
- Approximately six months — Enagic's store listing for the FC1.
- Approximately one year — the LeveLuk K8 manual, alongside the 6,000 litre figure.
Read together, Enagic's own figures put a filter's life somewhere between six and twelve months for most households, arriving sooner where more water is drawn and where the source water is harder or more heavily treated. A household of ten reaches 6,000 litres considerably faster than a household of two.
Machines that track filter life count both elapsed time and volume and indicate when replacement is due on either count. They do not detect clogging.
Capacity and construction
Enagic states the FC1 is a molded activated carbon filter with high-density micro-pores, with inner and outer non-woven fabric layers. Capacity is stated as approximately 1,500 gallons, which is the same figure as the 6,000 litres above.
Enagic states it reduces residual chlorine, surfactants and agricultural chemicals such as herbicides, and that flow rate is up to 30% higher than the filters it replaces.
Genuine filters
Enagic's own position, reproduced because it affects the warranty rather than because it is our view:
Using non-genuine replacement filters, including counterfeit or unauthorised filters, immediately voids the manufacturer's warranty. Enagic states these may reduce performance, affect water quality and risk damaging the machine, and that it takes no responsibility for malfunctions, internal electrical damage, water quality issues or performance problems that result.
Some machines recognise a genuine filter and reset the filter history automatically when one is fitted. Enagic states that a filter it does not recognise causes the machine to mis-measure water volume.
What isn’t published
Enagic publishes three different replacement intervals for the same filter — 6,000 litres, approximately six months, and approximately one year — across its store listing and the K8 manual. The variation is explained by usage and water quality, but Enagic publishes no method for working out which figure applies to a given household.
No FC1-specific installation video is published. The video this guide follows is Enagic's general replacement-filter video.
No per-substance reduction figures are published for the FC1. Enagic names residual chlorine, surfactants and agricultural chemicals, but gives no percentage for any of them and no test standard. The LeveLuk K8's manual publishes an NSF/ANSI 42 result for its own filter; nothing equivalent is published for the FC1.
The 30% flow rate increase is stated without a baseline. Enagic does not say whether it is measured against the F8, the HG-N, or both.
Sources
Enagic's own published material: the replacement filters page, the FC1 store listing, and Enagic Canada's installation video. The replacement interval figures also draw on the LeveLuk K8 operation manual.
Questions
Which machines take the FC1 filter?
Every Enagic machine that previously used an F8 or an HG-N filter. Enagic's rule is to open the cover and read the label on the current filter: F8, HG-N or FC1 all mean order the FC1. A filter labelled MW-7000HG or HG takes the HG filter instead.
How often should an FC1 filter be replaced?
Enagic publishes approximately 6,000 litres, approximately six months on its store listing, and approximately one year in the K8 manual. Filter life depends on how much water is drawn and on the source water, so a large household reaches the volume figure much sooner than a small one. Between six and twelve months covers most cases.
What are the O-rings for?
The bottom of the filter has two O-rings of different sizes, one per hole, with the large one in the centre hole. They seal the filter to the tray. If they stay behind in the tray when the old filter comes out, they must be refitted to the filter before the new one is installed.
Why run water before putting the cover back on?
To check for leaks while they are still visible. Enagic's video runs water for a couple of minutes with the cover off, which is the point at which a badly seated filter or a missing O-ring shows itself.
The filter holder will not turn. What now?
Enagic's own advice is to clean the rail that the filter holder runs along and try again.
Does a non-genuine filter matter?
Enagic states that using one immediately voids the manufacturer's warranty, and that it takes no responsibility for machine malfunctions, electrical damage or water quality problems that result. Machines that recognise a genuine filter also reset their own filter history when one is fitted.
What does the FC1 remove?
Enagic states residual chlorine, surfactants and agricultural chemicals such as herbicides. No reduction percentage or test standard is published for the FC1 itself.